Choose the appliance you're having trouble with to learn more about the specific repair service.
A refrigerator depends on proper airflow, temperature regulation, refrigeration components, sensors, fans, and controls working together to hold a safe temperature. When one part of that chain fails, the symptom you notice is often several steps removed from the actual cause.
- Refrigerator not cooling
- Refrigerator running too cold
- Temperature fluctuations
- Water leaking onto the floor
- Excessive frost or ice buildup
- Refrigerator running continuously
- Unusual noises
- Ice maker problems
- Water dispenser problems
When a fridge isn't holding the proper temperature, the underlying problem can involve airflow, temperature regulation, defrost components, fans, sensors, or controls. Small temperature swings often show up long before the unit stops cooling entirely.
- Fridge section warm while freezer stays cold
- Food spoiling faster than expected
- Condensation inside the cabinet
- Water pooling under the crisper drawers
- Frost accumulating on the back wall
- Clicking, buzzing, or humming noises
A freezer that cannot hold the correct temperature puts frozen food at risk quickly. Both upright and chest freezers, as well as freezer compartments in combination units, rely on consistent airflow and a working defrost cycle.
- Freezer not freezing
- Food beginning to thaw
- Excessive frost or ice buildup
- Freezer running continuously
- Water leaking from the unit
- Unusual noises
- Temperature instability
Modern washing machines depend on proper water supply, drainage, motors, sensors, lid or door locking systems, and electronic controls. A cycle that stalls partway through is usually the machine protecting itself after a sensor reading it didn't expect.
- Washer not starting
- Washer not filling
- Washer not draining
- Washer not spinning
- Washer stopping mid-cycle
- Door or lid not locking
- Water leaks
- Excessive shaking or walking
- Unusual noises
- Error codes on the display
A dryer problem may involve heating components, airflow, sensors, motors, belts, switches, electrical supply, or electronic controls. Electric and gas dryers fail in different ways, so the diagnosis path differs as well.
- Dryer not heating
- Dryer won't start
- Drum not turning
- Clothes taking too long to dry
- Dryer stopping during a cycle
- Unusual noises or squealing
- Dryer running without drying clothes
- Error codes
A dishwasher relies on proper filling, water circulation, heating, drainage, and electronic control throughout each cycle. Poor cleaning results are often the first sign that one of those stages isn't completing.
- Dishwasher not starting
- Dishwasher not filling
- Dishwasher not draining
- Dishwasher leaking
- Poor cleaning results
- Dishes remaining wet
- Unusual noises
- Error codes
An oven has to reach and hold a target temperature accurately. When baking results change or the display reports a fault, the cause may be a heating component, a sensor reading, or the control that manages both.
- Oven not heating
- Oven overheating
- Uneven baking
- Gas oven won't ignite
- Temperature not matching the setting
- Broil element not working
- Door not sealing or latching
- Error codes
Stove problems tend to show up one burner at a time. Whether the range is gas or electric changes what has to be tested, from spark modules and burner caps to surface elements and infinite switches.
- Burner won't heat
- Gas burner won't ignite
- Burner clicking continuously
- Uneven or weak flame
- Burner stuck on high
- Surface element only partly heating
- Control knob or switch problems
Built-in cooktops — radiant, induction, and gas — use different heating methods but share the same requirement for clean, correct control signals. Glass-top and induction models add sensors that shut heating down when something is out of range.
- Cooktop not heating
- Induction burner not recognizing cookware
- Element cycling on and off too quickly
- Ignition failure on gas burners
- Touch controls unresponsive
- Error codes on the control panel
A garbage disposal is a small motor working in a wet environment under the sink. Most failures fall into one of three categories: it's jammed, it's lost power, or the housing has begun to leak.
- Disposal won't start
- Humming without turning
- Jammed grinding chamber
- Leaking at the sink flange or housing
- Loud rattling or grinding noises
- Disposal shutting off during use